Fantastic idea! Now, we will need to drill a pilot hole for these. So, at this point, what we're gonna do is take the end of our strap. Again, these are gonna be side-specific. Subscribe: New Wrangler videos daily! But you can find them at your local hardware store, and they are pretty inexpensive. Thank you .. Ive been racking my brain for three days now trying to get something to work. So we're working on the JL two-door left, which is the driver's side, and we are going to mount it on the outside of this rubber stopper here, on the underside of the hardtop. So, taking the hardtop off of your Jeep is definitely one of the best experiences that the Jeep has to offer. So, I have a marker and my plum. Still not sure what the best solution is to mount the hardtop to the hoist. Now, in comparison to some other options on the page, like I said, this is going to be a pretty simple system. There is a small gap between the cap end of the hook and the roof so it is resting more on the U part of the hook. You're gonna wanna make a mark when the Jeep is in the garage to make sure that it's gonna be in the same location every time, then you can take the hardtop off the same way that you always would and place that in the same location, so we can install our guides and make some measurements on our ceiling so we can install our hoist.So, our first step to what we're gonna do is install our guides. I initially went the pulley method however it must require a little engineering as I think my plan made the top heavier. Now, in the front, we're just gonna measure 12 inches forward and we're gonna do the same thing for the front. And you'll be able to kind of push up on the hardtop to get it level with your Wrangler. TACOMA, TACOMA SR, TACOMA SR-5, TOYOTA RACING DEVELOPMENT (TRD), TACOMA LIMITED, TUNDRA, TUNDRA SR, TUNDRA SR-5, TUNDRA TRD PRO, TUNDRA LIMITED, 4RUNNER, 4RUNNER SR-5, 4RUNNER LIMITED, 4RUNNER NIGHTSHADE, AND 4RUNNER TRD OFFROAD ARE REGISTERED TRADEMARKS OF TOYOTA MOTOR CORPORATION. Now, from the center, we're gonna need to measure out 20 inches either way. I just have some hardware tied to the end of it, you can take a nut or a washer and tie it to the end of the string. Now, this is gonna be where our 2x6 is gonna be located. Now, my rafters are parallel to my setup here, so I'm gonna be mounting up my 2x4 or my 2x6 perpendicular. And you can trust that this is going to, not only very easily take the hardtop off of your Wrangler, but it's also going to safely store it in the air, making sure that you're saving storage space inside your garage or wherever you're mounting the hoist.Not to mention this is also going to come with guides to make sure that the straps are staying in place and that the straps are not sitting directly on the hardtop and damaging any of the finishes on the hardtop itself.Now, with all of that being said, this is gonna come in at roughly $100. So, today we're checking out the Redrock 4x4 manual hardtop hoist, fitting all 2018 and newer two-door JL Wranglers. And then, we can lift our hardtop off of our Wrangler.At this point, our hardtop hoist is installed and all we have to do, at this point, is lift the hardtop off of our Wrangler. Please use the drop down menu to select. And continue to screw it in until the threads stop. So, speaking of that install, let me walk you through that right now.The tools that I used for my install were an impact wrench, a 3.16 and a 13/16 inch drill bit. Make sure you like and subscribe for more videos and products just like this. I envy all of you topless JK'ers. The J-BARR system allows one person to easily remove and store their hardtop. Ownership does not affect chances of winning, Review & Install - RedRock Manual Hard Top Hoist Video. I use 4 bicycle hooks in the ceiling with ratchet straps - $20 out the door. And that's gonna start to drop our hardtop into place. We can take our square. Care should be taken when hooking into the hard top, by using some cloth or foam. (I'd be storing mine for about 9 months out of the year) Thanks! So we are gonna wanna measure that and make a mark so it's measured correctly and we can get the correct measurement on our ceiling. So, at this point, what we're gonna do is take the end of our strap. The one below has the top resting on 24 lumber, and rope ratchets are used to raise and lower the hart top. However, you can find that at your local hardware store, and they are pretty inexpensive.So, at this point, what we can do is take our 2x4 or 2x6, whatever you're using at home, and we can mount that up on the marked locations at that 12-inch mark. You wanna make sure that you're paying attention to the JL two door, they are gonna be side-specific. Come join the discussion about reviews, performance, trail riding, gear, suspension, tires, classifieds, troubleshooting, maintenance, for all JL, JT, JK, TJ, YJ, and CJ models! Light to Moderate mechanical skill required. And storing it is not that easy, considering the size of the hardtop itself.Now, getting a hoist is a very easy solution to all of those problems. But right now, we are just going to measure this out, make a mark with a square. Click here to download complete install and use guide. Then we can do the same thing for the other side.Next, we can take our rear guides and put them into each of the corners of the hardtop. Any pics of how the J-hooks are used? And this option by Redrock 4x4 is going to be one of your most affordable and your most user-friendly options in order to do that.Now, this system is gonna come with a 4. system, so you're gonna have all of the heavy-duty hardware that you need to mount to the ceiling in your garage. So, for the front, again, they have to be 25-inches apart. Most Jeep owners will also remove the doors when removing the hard top to get the full open air experience. However, you can mount up your 2x4 or your 2x6 individually. So, I have a marker and my plum. Now, in the front, we're just gonna measure 12 inches forward and we're gonna do the same thing for the front. By entering your cell phone number, you agree to receive recurring text messages using an automatic telephone dialing system at the cell number provided when signing up. We're gonna drill in the center of the mark that we've made on either side. Well designed site; very easy to find what I'm interested in by using the filters provided. This one is using inexpensive bicycle hoists to lift the top. You wanna make sure that you're paying attention to the JL two door, they are gonna be side-specific. I'm leaning towards the Racor lift but - in true Jeepster fashion - with some modifications to use j-hooks or straps or perhaps a combination of the two. And then, you'll be all set to go.That's gonna wrap it up for my review and install. | It will still be up out of the way. Details. But I'm gonna take this, as well as a T20 TORX bit, or TORX socket, and secure those down. Now, this step is going to depend on how your garage is set up and how the rafters are set up in your garage. Now, if you are in a garage that has perpendicular rafters, you're just going to do the opposite, you're going to mount it up parallel to your garage.Now, the 2x4s and the 2x6s, as well as the hardware that you are going to mount this up with, is not included in the kit. This site uses cookies to provide you with the best experience possible. Privacy Policy Is there a reason you didn't use ratcheting straps?? Tires and Wheel and Tire Kits do not qualify for free shipping. So that is where it needs to be. But I'm gonna take this, as well as a T20 TORX bit, or TORX socket, and secure those down. Now, from the center, we're gonna need to measure out 20 inches either way. Conversely, when lowering the hard top back onto the jeep, one simply needs to press the cam button while holding tension on the strap, and gently lower each corner a little at a time, until it rests back onto the tub of the Jeep. So, now that that's sitting in the front and the rear guide and it's tight, we can repeat that on the other side. So, I made a small mark. I might try asking around the motor pool, CE, or if you have a do it yourself auto shop on base, one of those might have someplace in a fenced in lot you could store it. So we're gonna have a mark for each of our guides, then we're gonna measure out where we need to put our 2x6s. And then, we can go ahead and secure it down with some wood screws.So, mine spans the length or the width of my structure here. Once the hardtop's back on the Jeep, we can undo our straps on either side.Now, in order to put your T-tops, as well as the back glass down, you will need to remove the guides. And then, do the same thing for all the other guides.So, what we can do right now, since we have made our measurement of where our plum sat with our guide, I'm working in the rear right now but what I'm gonna do is take this measurement and measure 12 inches back. Does anyone use the platform to store doors? Like I said, this is a very affordable option for a hardtop hoist. Ya I guess that makes sense. And we are going to hang it from the ceiling and align it with our guides. Then, we can repeat that process in the back.So, what we can do, at this point, is take the longer part of our straps and we can hang it on our front eyelet, on either side. And do the same thing for the other one. So we're gonna have a mark for each of our guides, then we're gonna measure out where we need to put our 2x6s. So, after you're finished using your hardtop hoist, you wanna make sure that you are securing your hardtop correctly with all of the factory hardware. Msg and data rates may apply. I have always loved the outdoors and with my camping experiences, it brought me into the Jeep world. I've seen a lot of people wrap straps around the entire hardtop but that seems process intensive. Instructions for door removal are available online, but there are some tips that you may want to be aware of in the discussion below, and you will also find more tips online in some forums. This is just going to be a string with something heavy tied to the end of it. So what I'm gonna do is take my tape measure, as well as my marker and my square, and make a mark from the center out 20 inches on either side. I just put a racor I'm the garage, but its winter in the midwest. So, after you're finished using your hardtop hoist, you wanna make sure that you are securing your hardtop correctly with all of the factory hardware. Please complete the following steps to add to cart: We're sorry. Then we can use an extension to help screw them in.So, you can kind of get it started by hand, but then, you can take an extension. If you continue to use this site we will assume that you are happy with it. And storing it is not that easy, considering the size of the hardtop itself.Now, getting a hoist is a very easy solution to all of those problems. By entering your email, you agree to receive recurring automated marketing emails from ExtremeTerrain at the email provided. The Fora platform includes forum software by XenForo, www.brandywinegraphics.com/vinylproducts.html, http://www.jkowners.com/forum/showthread.php?t=35749, VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada. And continue to screw it in until the threads stop. I took my top off a few weeks ago with the hopes of putting it in the basement; alas the door frames and hallways in military housing are too narrow. So, speaking of that install, let me walk you through that right now.The tools that I used for my install were an impact wrench, a 3.16 and a 13/16 inch drill bit. JavaScript is disabled. The installation in the first image below, shows how a bar was used to connect to the joists, then the straps were placed in the optimum location on the bar to hook into the hard top. You wanna make sure that you're not overtightening this, you wanna make sure that you tighten it just to that lift there, that last thread, and you wanna make sure that you don't undertighten it either. This is gonna come with four heavy-duty straps to allow you to very easily take the hardtop off of your Wrangler. Line that up. Now, my rafters are parallel to my setup here, so I'm gonna be mounting up my 2x4 or my 2x6 perpendicular. So, I made a small mark. And always keep it right here at extremeterrain.com. All Rights Reserved And for $100, you really can't beat it.Now, as far as the install is concerned, I'm gonna give this a 2 out of 3 wrenches on the difficulty meter, taking you about 3 hours to get the job done in your garage. At this point one can just lift each corner of the top by pulling on the strap. So we're working on the JL two-door left, which is the driver's side, and we are going to mount it on the outside of this rubber stopper here, on the underside of the hardtop. And then, we can go ahead and work on our hoist.So, what we can do next is install our front guides, they are gonna be labeled. Reply HELP to 94985 for help. It has always been a dream to own a Wrangler of my own and recently I was able to acquire one of my own! With this set up, one merely needs to back into their garage, then on each side hook the straps in the rear corner, and near the front of the hard top, as shown in the image below. The cart can be constructed on wheels in order to move it around where needed. You don't need to use a stud finder in order to do this. ExtremeTerrain is proud to offer FREE SHIPPING on any order over $75! If using either of the above straps, they must be secured to the joists in your garage ceiling. And this option by Redrock 4x4 is going to be one of your most affordable and your most user-friendly options in order to do that.Now, this system is gonna come with a 4. system, so you're gonna have all of the heavy-duty hardware that you need to mount to the ceiling in your garage. 2003-2022 ExtremeTerrain.com. This is the left and the passenger side is gonna be the right.So I added a piece of painters tape here, I'm gonna do the same thing on the other side. So, from the center, we're gonna measure out 12.5 inches.So, what we can do now is attach our eyelag screws. So we are gonna wanna measure that and make a mark so it's measured correctly and we can get the correct measurement on our ceiling. I have a little bit of painters tape here, just to keep them in place while we get our measurements. Subscribe to our YouTube Channel, Features, Description, Reviews, Q&A, Specs & Installation, CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. If youre only going to remove the hard top once in a while, considering inexpensive solutions as addressed in this article and this video, will leave you more money left over, to possibly get more other things for your Jeep. I would recommend to drill a pilot hole. So, after this front one is attached, we can repeat that same process in the back.So, now that we have our 2x6s installed, what we can do is measure out where we need to mount our eyelet screws. :whistling: Can't beat the RACOR hoist and I use "J" hooks with my rack !! But it won't be able to pull from the other side, making sure that our hardtop is secured. So, taking the hardtop off of your Jeep is definitely one of the best experiences that the Jeep has to offer. An equally inexpensive strap solution is the use of cam straps. However, when you have a hardtop, that can be pretty difficult, considering that the hardtop is heavy, it's awkward to take off. And then, do the same thing for all the other guides.So, what we can do right now, since we have made our measurement of where our plum sat with our guide, I'm working in the rear right now but what I'm gonna do is take this measurement and measure 12 inches back. Seems to be a lot of you that are like me and don't want to drop big $$$ on a hard top hoist, so I thought I'd throw this idea out for y'all. Any thoughts? There are many options available for storage of the doors when they get removed. So, today we're checking out the Redrock 4x4 manual hardtop hoist, fitting all 2018 and newer two-door JL Wranglers. Some other options will usually include a crank system, they may include a pulley system, or they are going to include a winch or something, as far as the electronics are concerned, which will make it a little bit more expensive and a little bit more difficult to install. Thanks to a 5" elevated slab in my garage (the previous owner poured in) the Jeep can't clear the garage door, let alone have enough room for a hoist to lift the top off. But I really think that that shines through considering that it makes it very easy to use. Simple and cheap. You wanna make sure that you're not overtightening this, you wanna make sure that you tighten it just to that lift there, that last thread, and you wanna make sure that you don't undertighten it either. Like I said, this is a very affordable option for a hardtop hoist. So I'm just gonna take a tape measure and a marker and mark on the painters tape where that's supposed to sit. Then we can do the same thing for the other side.Next, we can take our rear guides and put them into each of the corners of the hardtop. But it won't be able to pull from the other side, making sure that our hardtop is secured. A forum community dedicated to Jeep Wrangler owners and enthusiasts. Also, there are low cost solutions to protect your Jeep, and doors from damage in the process. I just have some hardware tied to the end of it, you can take a nut or a washer and tie it to the end of the string. So that is where it needs to be. Act Like It. We're sorry, zip can't be updated at this time. Now, with this system, again, you're going to evenly pull, which will make it very easy to take the hardtop off of your Jeep. I'm not sure yet how I'm going to connect the hardtop to it. This is the left and the passenger side is gonna be the right.So I added a piece of painters tape here, I'm gonna do the same thing on the other side. You kind of wanna make sure that [inaudible 00:04:23] butted up against there.Now, once that's in place, I'm just gonna take a piece of painters tape and just secure this down. Ours are exposed, so I don't necessarily need that tool. Such a hoist can be seen on this video, as described below. I have a little bit of painters tape here, just to keep them in place while we get our measurements. And up at the front, they need to be about 25-inches apart. Your my hero; I've been beating myself up trying to this without spending 2 bills. Rugged Ridge All-Terrain Door Entry Guards (18-22 Jeep Wrangler JL 2-Door), Rugged Ridge Full-Length Eclipse Sun Shade; Black (18-22 Jeep Wrangler JL 2-Door), Teraflex Full Hard Door Hanger (07-22 Jeep Wrangler JK & JL), Hi guys. You can just lift up on the hardtop, just wiggle those out. So, after this front one is attached, we can repeat that same process in the back.So, now that we have our 2x6s installed, what we can do is measure out where we need to mount our eyelet screws. And do the same thing for the other one. However, these straps have the advantage of allowing one to lower the hard top in a controlled fashion, by depressing the button on the strap when pulling on it to lift the top, or releasing the strap when lowering the top. I've been looking into all kinds of different ways to hoist off my top solo, (the girlfriend.. while pretty, is kinda weak and scared to help, The rubicon is a 29 km. Then we can use an extension to help screw them in.So, you can kind of get it started by hand, but then, you can take an extension. Receive text messages for special offers and discounts. Auto - 4.10s - AEV: 3.5" SC lift, Milspec front bumper, rear bumper, tire carrier w/ hi-lift mount, front skid plate, high-steer - Warn XD9000i w/ Viking Winchline - 35" BFG MTs - Hellas - Katzkin Leather - RAM iPad mount - Cobra 75/Firestik - Poison Spyder Fairlead - Mopar Enhanced Rock Rails - aFe y-pipe - Rock Hard Oil Pan/Engine Skid - 10lb PowerTank, The Fora platform includes forum software by XenForo, VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada. Flat rate shipping. We're gonna go up to the ceiling and drop this down so we can align it with our front guides.We can make a mark, label it. Now, I would like to mention that you will need at least a 7-foot-tall ceiling with room underneath to park your jeep in order to install this, and that the 2x4s or 2x6s, as well as some of the hardware, in order to mount those to the studs in your garage, are not included in the kit. We're going to send it over the roll bar underneath the hardtop and we're gonna align it with our guide up at the front. Now, we wanna kinda make sure that we're doing this evenly. Haven't had a problem yet. Any worries about the top bending over time stored in this manner? And then, you'll be all set to go.That's gonna wrap it up for my review and install. Truck freight and oversize charges still apply unless otherwise noted, and can only be shipped to the lower 48 States. We couldn't save this product at this time. You wanna make sure that it's centered on that line there.So, at this point, now that we have our 2x4 in place, you're gonna want to secure it down. You wanna make sure that we're not wrapping it around the roll bar because then we won't be able to lift the hardtop off the Jeep. Another option would be to secure a 26 to the joists, and then secure the straps in their optimum location by screwing into the 26, as in the second image below. Once the hardtop's back on the Jeep, we can undo our straps on either side.Now, in order to put your T-tops, as well as the back glass down, you will need to remove the guides. You don't need to use a stud finder in order to do this. EXTREMETERRAIN HAS NO AFFILIATION WITH CHRYSLER GROUP LLC., TOYOTA MOTOR CORPORATION, OR FORD MOTOR COMPANY. No guide available for this part yet. I've had my top of 7 times since August and no issues. We're gonna send this to the back, I just wanna make sure that the strap is sitting in the guide correctly. We can do the same thing on the other side. Then, we can repeat that process in the back.So, what we can do, at this point, is take the longer part of our straps and we can hang it on our front eyelet, on either side. Hi, I've been lurking for a while, this is my 1st post. And for $100, you really can't beat it.Now, as far as the install is concerned, I'm gonna give this a 2 out of 3 wrenches on the difficulty meter, taking you about 3 hours to get the job done in your garage. Reply STOP to 94985 to cancel. We're gonna send this to the back, I just wanna make sure that the strap is sitting in the guide correctly. Rough Country items are not included in Free Shipping offers. Now, in comparison to some other options on the page, like I said, this is going to be a pretty simple system. We can do the same thing on the other side. Questions..call us at 309-214-9393, How to measure for an older or custom hardtop. What we're gonna do in a second is take a plum and measure it from the ceiling down to the guide to make sure that we're getting the correct measurement on our ceiling. What we're gonna do now is take our strap and open up our cam buckle. Please enter your email to save your Virtual Build. Ours are exposed, so I don't necessarily need that tool. And that is where we're gonna mount up our 2x6. Made in the USA. So, for the front, again, they have to be 25-inches apart. The "hooks" are flat, spread out the load more than a j-hook. A dead blow to line this up. It is going to list JK two-door as well. Then we can actually just send the rest of this to the trunk or the cargo area. It is going to list JK two-door as well. And then, we can go ahead and work on our hoist.So, what we can do next is install our front guides, they are gonna be labeled. And the JK and the JL are gonna be opposite. I have already done so with a 3/16-inch drill bit. They need to be about 40 inches apart. Now, this step is going to depend on how your garage is set up and how the rafters are set up in your garage.
Pleated Midi Skirt Green, Simpson Ps3425 Manual, Stove In Island Without Vent, Phv1810 Battery Replacement, Binding Post Screws Ace Hardware, Liquid-plumr Disposal And Drain Foaming Cleaner, Black And Decker Gh710 Line Replacement, Deanna Denim Shirt Dress Black, Pressure Reducing Valve Watts,